HD Eye Nut Dwg.

Drop Forged Wire Rope Clips

For more information about Chicago Hardware and Fixture products go to their website at: http://www.chicagohardware.com/


Drop Forged Wire Rope Clips

Should be used in heavy duty applications
Meets Performance Requirements of Federal Specification FF-C-450, Type 1, Class 1
For Lighter-Duty applications see Malleable Wire Rope Clips or 304 SST Clips
Hot
Galvenized
U-Bolt Dimensions Weight
Rope Size Part No. A B C T Per 100
1/8 23460 3 12-24 3/4 9/32 1/2 6.5
3/16 23456 8 1/4-20 15/16 5/16 5/8 10
1/4 23470 2 5/16-18 1-5/32 3/8 3/4 18.5
5/16 23475 7 3/8-16 1-1/2 1/2 1 29.5
3/8 23480 1 7/16-14 1-5/8 9/16 7/8 44
7/16 23485 6 1/2-13 1-7/8 5/8 1-1/4 64
1/2 23490 0 1/2-13 1-7/8 5/8 1-1/4 75
9/16 23495 5 9/16-12 2-3/8 3/4 1-3/8 106
5/8 23500 6 9/16-12 2-3/8 3/4 1-3/8 106
3/4 23505 1 5/8-11 2-3/4 7/8 1-5/8 153
7/8 23510 5 3/4-10 3-1/4 1 1-7/8 237.5
1 23515 0 3/4-10 3-5/8 1-1/8 2 272.5
1-1/8 23520 4 3/4-10 3-13/16 1-1/4 2-1/4 325
1-1/4 23525 9 7/8-9 4-3/8 1-11/32 2-1/2 441
1-1/2 23535 8 7/8-9 5-1/8 1-11/16 2-3/4 550
Dimensions are in inches. Weights are in pounds.




Recommended Application For
Chicago Drop Forged Wire Rope Clips

1. The correct way to attach wire rope clips is illustrated above. Apply the first clip one base width from the dead end of the wire rope. The base or saddle should bear on the line end of the rope - U-bolt on the short end. Tighten nuts firmly.

2. Attach second clip as close to loop as possible. Tighten nuts, but not firmly.

3. Attach balance of clips spaced equally between the first two clips. Tighten all nuts completely. Apply initial load - inspect nuts and retighten. Inspect all clips periodically.

The number of clips shown is based on using right regular or Lang lay wire rope, 6 x 19 class or 6 x 37 class, fibre core IWRC, IPS or XIPS. The number of clips shown also applies to right regular wire rope, 8 x 19 class and 18 x 7 class, fibre core, IPS or XIPS, sizes 1-1/2-inch and smaller.

If Seale construction or similar large outer wire type construction in the 6 x 19 class is to be used for sizes 1-inch and larger, add one additional clip. For other classes or wire rope not mentioned, it may be necessary to add additional clips to the number shown. If more clips are used than shown, amount of rope turn back should be increased proportionately.

Clip
Size
Minimum
No. of
Clips
Amount of Rope
to Turn Back
Torque in
Ft. Lbs
1/8 2 3-1/4 4.5
3/16 2 3-3/4 7.5
1/4 2 4-3/4 15
5/16 2 5-1/4 30
3/8 2 6-1/2 45
7/16 2 7 65
1/2 3 11-1/2 65
9/16 3 12 95
5/8 3 12 95
3/4 4 18 130
7/8 4 19 225
1 5 26 225
1-1/8 6 34 225
1-1/4 7 44 360
1-1/2 8 54 360




Smith Fastener Company • 3613 East Florence Avenue, Bell, California, 90201
Phone: ( 323 ) 587-0382 • FAX: ( 323 ) 587-8712 • E-mail: [email protected]
Copyright © 2009 by Smith Fastener Company

Hitch Pins | Construction/Lifting | Blind Rivets | Dowel Pins | Cotter Pins | Nuts, Bolts, Screws, Washers
Threaded Inserts | Anchors | Pins | Automotive | Weatherhead Pipe Fittings | Cutting Tools