Red Head® Epcon®
G5 Epoxy Anchoring Adhesive

A strong extended working time epoxy adhesive.




The advantages of Epcon G5 Epoxy Adhesive are numerous

  • Nozzles last longer - saving money
  • Gives more time to install anchors
  • Easier to install anchors in hot weather
  • Easier installation of larger diameter anchors and deeper embedments
  • Odorless
  • Extended Working Time
    • G5 provides 45 minutes nozzle life and 8 hour cure time at 70 degrees F.
EPCON G5

Number of Anchoring Installations per Cartridge*
Using Reinforcing Bar with G5 Adhesive in Solid Concrete

18 Fluid Ounce Cartridge
Rebar Hole
Dia
Inches
Embedment Depth in Inches (mm)
1
(25.4)
2
(50.8)
3
(76.2)
4
(101.6)
5
(127.0)
6
(152.4)
7
(177.8)
8
(203.2)
9
(228.6)
10
(254.0)
11
(279.4)
12
(304.8)
13
(330.2)
14
(355.6)
15
(381.0)
#3 1/2 316.7 158.4 105.6 79.2 63.3 52.8 45.2 39.6 35.2 31.7 28.8 26.4 24.4 22.6 21.1
# 4 5/8 239.3 119.6 79.8 59.8 47.9 39.9 34.2 29.9 26.6 23.9 21.8 19.9 18.4 17.1 16.0
# 5 3/4 183.5 91.8 61.2 45.9 36.7 30.6 26.2 22.9 20.4 18.4 16.7 15.3 14.1 13.1 12.2
# 6 7/8 148.2 74.1 49.4 37.0 29.6 24.7 21.2 18.5 16.5 14.8 13.5 12.3 11.4 10.6 9.9
# 7 1-1/8 71.0 35.5 23.7 17.7 14.2 11.8 10.1 8.9 7.9 7.1 6.5 5.9 5.5 5.1 4.7
# 8 1-1/4 63.2 31.6 21.1 15.8 12.6 10.5 9.0 7.9 7.0 6.3 5.7 5.3 4.9 4.5 4.2
# 9 1-3/8 65.9 33.0 22.0 16.5 13.2 11.0 9.4 8.2 7.3 6.6 6.5 5.5 5.1 4.7 4.4
# 10 1-1/2 53.9 27.0 18.0 13.5 10.8 9.0 7.7 6.7 6.0 5.4 4.9 4.5 4.1 3.9 3.6
# 11 1-3/4 33.0 16.5 11.0 8.2 6.6 5.5 4.7 4.1 3.7 3.3 3.0 2.7 2.5 2.4 2.2
* The number of anchoring installations is based upon calculations of hole volumes using ANSI tolerance carbide tipped drill bits, the nominal areas of the reinforcing bars and the stress areas of the threaded rods. These estimates do not account for waste.



EPCON G5

Number of Anchoring Installations per Cartridge*
Using Threaded Rod with G5 Adhesive in Solid Concrete

18 Fluid Ounce Cartridge
ROD
DIA
HOLE
DIA
EMBEDMENT DEPTH IN INCHES (MM)
1
(25.4)
2
(50.8)
3
(76.2)
4
(101.6)
5
(127.0)
6
(152.4)
7
(177.8)
8
(203.2)
9
(228.6)
10
(254.0)
11
(279.4)
12
(304.8)
13
(330.2)
14
(355.6)
15
(381.0)
IN (mm) INCHES
1/4 (6.4) 5/16 587.3 293.7 195.8 146.8 117.5 97.9 83.9 73.4 65.3 58.7 53.4 48.9 45.2 42.0 39.2
3/8 (9.5) 7/16 340.0 170.0 113.3 85.0 68.0 56.7 48.6 42.5 37.8 34.0 30.9 28.3 26.2 24.3 22.7
1/2 (12.7) 9/16 244.7 122.4 81.6 61.2 48.9 40.8 35.0 30.6 27.2 24.5 22.2 20.4 18.8 17.5 16.3
5/8 (15.9) 3/4 125.2 62.6 41.7 31.3 25.0 20.9 17.9 15.7 13.9 12.5 11.4 10.4 9.6 8.9 8.3
3/4 (19.1) 7/8 99.1 49.5 33.0 24.8 19.8 16.5 14.2 12.4 11.0 9.9 9.0 8.3 7.6 7.1 6.6
7/8 (22.2) 1 82.0 41.1 27.4 20.5 16.4 13.7 11.7 10.3 9.1 8.2 7.5 6.8 6.3 5.9 5.5
1 (25.4) 1-1/8 67.6 33.8 22.5 16.9 13.5 11.3 9.7 8.4 7.5 6.8 6.1 5.6 5.2 4.8 4.5
1-1/4 (31.8) 1-3/8 51.2 25.6 17.0 12.8 10.2 8.5 7.3 6.4 5.7 5.1 4.6 4.3 3.9 3.7 3.4
*The number of anchoring installations is based upon calculations of hole volumes using ANSI tolerance carbide drill bits, the nominal areas of the reinforcing bars and the stress areas of the threaded rods. These estimates do not account for waste,



EPCON G5

Number of Anchoring Installations per Cartridge*
Using Reinforcing Bar with G5 Adhesive in Solid Concrete

22 Fluid Ounce Cartridge
Rebar Hole
Dia
Inches
Embedment Depth in Inches (mm)
1
(25.4)
2
(50.8)
3
(76.2)
4
(101.6)
5
(127.0)
6
(152.4)
7
(177.8)
8
(203.2)
9
(228.6)
10
(254.0)
11
(279.4)
12
(304.8)
13
(330.2)
14
(355.6)
15
(381.0)
# 3 1/2 388.9 194.5 129.6 97.2 77.8 64.8 55.6 48.6 43.2 38.9 35.4 32.4 29.9 27.8 25.9
# 4 5/8 293.8 146.9 97.9 73.5 58.5 49.0 42.0 36.7 32.6 29.4 26.7 24.5 22.6 21.0 19.6
# 5 3/4 225.4 112.7 75.1 56.3 45.1 37.6 32.2 28.2 25.0 22.5 20.5 18.8 17.3 16.1 15.0
# 6 7/8 182.0 91.0 60.7 45.5 36.4 30.3 26.0 22.7 20.2 18.2 16.5 15.2 14.0 13.0 12.1
# 7 1-1/8 87.2 43.6 29.1 21.8 17.4 14.5 12.5 10.9 9.7 8.7 7.9 7.3 6.7 6.2 5.8
# 8 1-1/4 77.6 38.8 25.9 19.4 15.5 12.9 11.1 9.7 8.6 7.8 7.1 6.5 6.0 5.5 5.2
# 9 1-3/8 81.0 40.5 27.0 20.2 16.2 13.5 11.6 10.1 9.0 8.1 7.4 6.7 6.2 5.8 5.4
# 10 1-1/2 66.2 33.1 22.1 16.6 13.2 11.0 9.5 8.3 7.4 6.6 6.0 5.5 5.1 4.7 4.4
# 11 1-3/4 40.5 20.2 13.5 10.1 8.1 6.7 5.8 5.1 4.5 4.0 3.7 3.4 3.1 2.9 2.
* The number of anchoring installations is based upon calculations of hole volumes using ANSI tolerance carbide tipped drill bits, the nominal areas of the reinforcing bars and the stress areas of the threaded rods. These estimates do not account for waste.



EPCON G5

Number of Anchoring Installations per Cartridge*
Using Threaded Rod with G5 Adhesive in Solid Concrete

22 Fluid Ounce Cartridge
ROD
DIA
HOLE
DIA
EMBEDMENT DEPTH IN INCHES (MM)
1
(25.4)
2
(50.8)
3
(76.2)
4
(101.6)
5
(127.0)
6
(152.4)
7
(177.8)
8
(203.2)
9
(228.6)
10
(254.0)
11
(279.4)
12
(304.8)
13
(330.2)
14
(355.6)
15
(381.0)
IN (mm) INCHES
1/4 (6.4) 5/16 721.2 360.6 240.4 180.3 144.2 120.2 103.0 90.2 80.1 72.1 65.6 60.1 55.5 51.5 48.1
3/8 (9.5) 7/16 417.6 208.8 139.2 104.4 83.5 69.6 59.7 52.2 46.4 41.8 38.0 34.8 32.1 29.8 27.8
1/2 (12.7) 9/16 300.5 150.3 100.2 75.1 60.1 50.1 42.9 37.6 33.4 30.1 27.3 25.0 23.1 21.5 20.0
5/8 (15.9) 3/4 153.8 76.9 51.3 38.4 30.8 25.6 22.0 19.2 17.1 15.4 14.0 12.8 11.8 11.0 10.3
3/4 (19.1) 7/8 121.7 60.8 40.6 30.4 24.3 20.3 17.4 15.2 13.5 12.2 11.1 10.1 9.4 8.7 8.1
7/8 (22.2) 1 100.9 50.5 33.6 25.2 20.2 16.8 14.4 12.6 11.2 10.1 9.2 8.4 7.8 7.2 6.7
1 (25.4) 1-1/8 83.0 41.5 27.7 20.7 16.6 13.8 11.9 10.4 9.2 8.3 7.5 6.9 6.4 5.9 5.5
1-1/4 (31.8) 1-3/8 62.8 31.4 20.9 15.7 12.6 10.5 9.0 7.8 7.0 6.3 5.7 5.2 4.8 4.5 4.2
* The number of anchoring installations is based upon calculations of hole volumes using ANSI tolerance carbide tipped drill bits, the nominal areas of the reinforcing bars and the stress areas of the threaded rods. These estimates do not account for waste.


Installation

For more information about Red Head® products go to their website at:
http://www.itwredhead.com/



Smith Fastener Company • 3613 East Florence Avenue, Bell, California, 90201
Phone: ( 323 ) 587-0382 • FAX: ( 323 ) 587-8712 • E-mail: [email protected]
Copyright © 2009 by Smith Fastener Company

Hitch Pins | Construction/Lifting | Blind Rivets | Dowel Pins | Cotter Pins | Nuts, Bolts, Screws, Washers
Threaded Inserts | Anchors | Pins | Automotive | Weatherhead Pipe Fittings | Cutting Tools