Shoulder Type Machinery EyeBolt

Chicago Hardware
Forged Machinery or Hoist Eyes

Drop forged, C-1035, steel. Heat treated after forging. Self colored, zinc plated or hot dipped galvanized. Plain or shoulder type, blank or threaded. Threaded will be supplied unless otherwise specified. For more information about Chicago Hardware and Fixture products go to their website at: http://www.chicagohardware.com/



STOCK
NUMBERS
STANDARD SIZES
BLANK or THREADED
MAXIMUM
LENGTHS
AVAILABLE
Either
Pattern
THREAD
SIZE
MAXIMUM LOAD in Lbs.
PLAIN SHOULDER SHANK EYE PLAIN SHLDR
Dia. Length I.D. O.D. Straight
Pull
Straight
Pull
45°
Pull
1 21 1/4 1 3/4 1-1/4 3 1/4-20 500 500 125
2 22 5/16 1-1/8 7/8 1-1/2 4 5/16-18 900 900 225
3 23 3/8 1-1/4 1 1-21/32 4-1/2 3/8-16 1400 1400 350
4 24 7/16 1-3/8 1-3/32 1-27/32 4-1/2 7/16-14 2000 2000 500
5 25 1/2 1-1/2 1-3/16 2-1/16 4-1/2 1/2-13 2600 2600 650
6 26 9/16 1-5/8 1-9/32 2-9/32 4-1/2 9/16-12 3000 3000 750
7 27 5/8 1-3/4 1-3/8 2-1/2 4-1/2 5/8-11 4000 4000 1000
8 28 3/4 2 1-1/2 2-13/16 5 3/4-10 6000 6000 1500
9 29 7/8 2-1/4 1-11/16 3-1/4 5 7/8-9 7000 7000 1750
10 30 1 2-1/2 1-13/16 3-9/16 5 1.00-8 9000 9000 2250
11 31 1-1/8 2-3/4 2 4 2-3/4 1.125-7 10000 10000 2500
12 32 1-1/4 3 2-3/16 4-7/16 3 1.25-7 15000 15000 3750
14 34 1-1/2 3-1/2 2-1/2 5-3/16 3-1/2 1.50-6 19600 19600 4900
Vertical loads are based on a safety factor of 5 to 1. Maximum load ratings are based on a straight vertical lift in a gradually increasing manner. Angular lifts will significantly lower maximum loads and should be avoided whenever possible. If angular lifting is required, a properly seated shoulder type eyebolt should be used. Loads should always be applied to eyebolts in the plane of the eye, not at some angle to this plane. Angular lifts should never be more than a 45° pull.

See also Standard Plain Eyebolts and Standard Shoulder Eyebolts



Smith Fastener Company • 3613 East Florence Avenue, Bell, California, 90201
Phone: ( 323 ) 587-0382 • FAX: ( 323 ) 587-8712 • E-mail: [email protected]
Copyright © 2009 by Smith Fastener Company

Hitch Pins | Construction/Lifting | Blind Rivets | Dowel Pins | Cotter Pins | Nuts, Bolts, Screws, Washers
Threaded Inserts | Anchors | Pins | Automotive | Weatherhead Pipe Fittings | Cutting Tools